The CS140 is a high-quality background luminance sensor. It provides the luminance data required to assess the visibility range for lights such as runway lights or warning lights.
The field of view and elevation angle follow aviation practice, and the spectral response follows the CIE curve that matches the typical response of the human eye.
The CS140 meets the standards required for Runway Visual Range, as well as the standards of ICAO, the UK CAA and the FAA. (This includes CAP670 and CAP746.)Leer más
The CS140 Background Luminance Sensor accurately measures background luminance over a wide range from 0 cd/m2 to a maximum of 45,000 cd/m2
The CS140 uses a photodiode with a spectral response close to the CIE human eye model and removes any unwanted wavelengths via an inbuilt band-pass filter.
The CS140 features a fixed 6˚ field of view as specified by the FAA. For ease of installation, the CS140 is simply mounted horizontally with the required 6˚ inclination already built into the design. (Other angles are possible via the sensor mounting bracket.)
The CS140 features a heated hood to prevent ice and snow from building up, dew heaters to prevent condensation on the glass window, and a dirty window detection system to measure window contamination.
The design is undamaged when pointed directly at the sun, allowing complete flexibility in orientation.
The CS140 has a rugged IP66 rated environmental enclosure that protects it from the harshest conditions and measures the atmosphere with high stability and repeatability.
|Measurement Range||0 to 45,000 cd/m2|
|Operating Humidity||0 to 100%|
|Wind Speed||Up to 60 m/s|
|Sensor Sealing||Rated to IP66|
|Response Time||1 s|
Stainless-steel V-bolt mounting to pole
Diameter 3.2 to 5.25 cm (1.26 to 2.07 in.)
|Sensor Dimensions||36 x 18 x 9 cm (14.2 x 7.1 x 3.5 in.)|
|Weight||~2.4 kg (~5.3 lb) dependent upon mounting system|
|Shipping Weight||3.5 kg (7.7 lb)|
Lower power states can be achieved by less frequent sampling and remote control of heaters.
Optional power supplies with battery back-up available.
A low-voltage shutdown level can be set to prevent back-up batteries from being damaged.
|Electronics Supply Voltage||9 to 24 Vdc|
|Hood Heater Supply Voltage||24 V dc or ac|
|Hood Heater Power||48 W|
|Dew Heater Power||0.6 W|
|Total Unit Power||< 1.5 W while sampling continously (including dew heater)|
|Serial Data Rates||1200 to 115,200 bps (38,400 bps default rate)|
|-NOTE-||Lens contamination circuitry monitors the window for contamination. The sensor can be configured to adjust calibration for contamination.|
|Field of View (FOV)||6° wide with sharp cut-off|
|Elevation Angle||6° with hood horizontal|
Nota: lo siguiente muestra información de compatibilidad notable. No es una lista de todos los productos compatibles.
|CR300||Using the CR300 with the CS140 is not recommended, as this would use the only RS-232 connection on the data logger.|
|CR310||Using the CR310 with the CS140 is not recommended, as this would use the only RS-232 connection on the data logger.|
|CR350||Using the CR350 with the CS140 is not recommended, as this would use the only RS-232 connection on the data logger.|
This sensor is compatible with any datalogger with a serial input.
Four example CR1000X programs are included that use the POLL, SET, SETNC, and GET commands for the CS140. Other data loggers are programmed similarly.
Release Note for Operating System OS10 for the Campbell Scientific CS140 Background Luminance Sensor
Campbell Scientific has introduced a new operating system, OS10, for the CS140 background luminance sensor. It is fully backwards compatible and is easily installed on all CS140 sensors. OS10 is available free of charge and can be downloaded from the Campbell Scientific website or supplied by email on request. Functionality, including data message formats is unchanged.