Con nuestros modems externos de telefonía móvil, tanto integradores, OEMs, como clientes finales, se pueden ahorrar tiempo y costosos gastos de viaje en visitas de mantenimiento a estaciones remotas.
La serie de modems externos CELL200 son dispositivos compatibles 4G LTE, que incluyen conectividad por puerto serie RS232 o puerto CS I/O. La red y operador lo determina la SIM que se introduzca en el modem.
El modem CELL215 tiene muy bajo consumo comparado con otros del mercado: 14 mA en reposo, 39 mA activo, y 300 µA en modo "low power".
Utilizado con nuestro servicio de datos en la nube de Campbell Scientific, estos modem no requieren ningun tipo de configuración.
El CELL215 forma parte de la serie de modems CELL200, que incluye:
Nota: El CELL215 no incluye tarjeta SIM, a menos que el modem se haya provisionado con/para nuestro servicio de datos en la nube; la tarjeta SIM debe adquirirse a un operador de telefonía móvil. Más información en Cellular Data Services page.
Leer másThe CELL215 is an industrial 4G LTE cellular module. It requires at least one micro-SIM 3FF card (for six position/contacts interface) supplied by your cellular carrier and a suitable 12 or 24 Vdc nominal power source. The CELL215 has an RS-232 serial port and a CS I/O port that can be used for serial server, serial client, and PPP host services. These ports are commonly connected to a data logger RS-232 serial or CS I/O port. The CELL215 has two antenna connectors to be used for primary and diversity antennas, although the unit can operate with only the primary cellular antenna connected.
The CELL215 provides Internet connectivity to any Campbell Scientific data logger located within range of a compatible cellular network. Armed with Internet connectivity, a data logger can remotely connect to Campbell Scientific software on a PC, mobile device, and the cloud. The CELL215 can also enable many data loggers to communicate using other Internet protocols, such as Modbus, DNP3, email, and web (HTTP).
The CELL215 provides highly reliable connectivity and remote device management independent of the device it is connected to. The numerous embedded services include IP serial server and client.
Campbell Scientific offers low-cost cellular data service plans for the CELL215. Our data service plans include Verizon in the United States and AT&T in North America (US, Mexico, Canada), as well as international access to over 600 carriers in 185 countries. The Konect routing service is included to assure a secure connection with Campbell Scientific data logger support software.
The CELL215 is configured using a web-based configuration tool hosted by the cellular module. It can be accessed using Internet Explorer or Firefox remotely over the cellular WAN (when in serial server mode) or via USB.
The CELL215 can also be configured directly from the data logger when used in PPP mode (default mode) using the Device Configuration Utility or CRBasic instructions.
Data loggers can be connected in a variety of ways to suit the needs of the application. Common methods include the use of serial or CS I/O cables.
Compared to many other industrial cellular modules, the CELL215 has extremely low power consumption. The average current consumption at 12 Vdc is approximately 14 mA when idle, depending on its configuration. Additionally, the CELL215 can be turned on and off easily using a data logger SW12V port or the IPNetPower() instruction (PPP mode for the CR1000X, CR300, and CR6 only). When using the SW12V terminal, the modem can typically be powered with a BP12 battery, a CH150 charging regulator, and an SP10 solar panel.
Campbell Scientific (Europe) offers two standard antennas for the CELL215. Our 2G/3G/4G/ 3dBi dBi pole mount antenna (Link to our 2G/3G/4G antenna page) connects directly to the CELL215 with a 3m cable. Where recommended by your cell provider, a MIMO version of the same antenna is also available (Link to the new MIMO antenna). Other higher gain antenna are available to special order for sites with long cable runs or weak signal strength (check with your cellular provider about the suitability and legality of high gain antenna on their network). Where long cable runs are used, on sites subject to static build-up, lightning protection may be needed, please call.
Certifications | IC (Industry Canada) 10224A-201611EC21A |
Host Interface |
|
RF Connectors | 2 SMA antenna connectors (primary and diversity) |
Operating Temperature Range | -40° to +80°C |
SIM Interface |
3FF (6 position/contacts) Supports SIMs that require 1.8 or 3 Vdc. |
Dimensions | 13.46 x 8.1 x 2.86 cm (5.3 x 3.19 x 1.13 in.) |
Weight | 215.5 g (7.6 oz) |
Cellular WAN |
|
Network Technology | 4G LTE CAT-1 (with automatic fallback to 3G and 2G) |
Carrier Approval | Vodafone |
4G LTE | 2100(B1), 1800(B3), 850(B5), 2600(B7), 900(B8), 800(B20) |
WCDMA (3G) | 2100(B1), 850(B5), 900(B8) |
GSM (2G) | 1800(B3), 900(B8) |
Data Speeds |
|
LTE |
|
WCDMA |
|
GSM EDGE |
|
GSM GPRS |
|
RS-232 or CS I/O | 9600 bps to 460.8 kps |
Power Consumption |
|
Low Power Mode | 300 µA |
Idle | 14 mA |
Active | 39 mA |
Radio Output and Sensitivity |
|
Output Power |
|
Sensitivity Range | -99.5 to 110.5 dBm (10 M) |
Note: In serial server mode, a cellular account with a static IP address is required.
Data Logger Model | Connecting to CELL215 via CS I/O Port | Connecting to CELL215 via RS-232 Port (choose one) |
CR300 and CR310 |
N/A |
|
CR6 |
16675 SC12 CS I/O cable |
|
CR1000X | 16675 SC12 CS I/O cable (PPP and serial server) |
|
CR200(X) Series |
N/A |
|
CR800 and CR850 |
16675 SC12 CS I/O cable |
|
CR1000 and CR3000 |
16675 SC12 CS I/O cable |
|
CR5000 |
N/A |
|
CR510 and CR10X |
N/A |
|
CR510-PB and CR10X-PB |
16675 SC12 CS I/O cable |
|
CR23X |
N/A |
|
CR23X-PB |
16675 SC12 CS I/O cable |
|
To update the CELL200 series operating system:
The update process can take 2 to 4 minutes.
Why Update? This OS resolves network registrations issues. Updated CELL205 to manage AT&T's shut down of its 3G network.
Three example programs as described in the CELL200-Series manual. The Power program shows how to control power to the CELL200 series by using the CRBasic
IPNetPower() instruction. The SetSettings example shows how to set up the cellular module using the SetSetting() instruction. It also illustrates how to retrieve status information from the module in the CRBasic program. The Settings example demonstrates using terminal commands.