Cumple IEC 61724-1
Resumen
The MetSens500 compact weather sensor measures wind speed and direction via an ultrasonic sensor, as well as air temperature, relative humidity, and barometric pressure, in a single, combined instrument mounted inside three double-louvered, naturally aspirated radiation shields with no moving parts. An integrated electronic compass allows the MetSens500 to provide accurate, relative wind direction measurements without being oriented in a particular way, making installation easier. WMO average wind speed and direction and gust, temperature, relative humidity, barometric pressure, absolute humidity, air density, and wet bulb temperature data are provided. The MetSens500 is compatible and easily integrated with the MeteoPV Solar Resource Platform and any Campbell Scientific data logger using SDI-12, RS-485, ModbusRS-485, or NMEA RS-232.
Ventajas y características
- Medidas de calidad
- Fácil y simple de instalar
- Compacto, diseño integrado
- Ligero y robusto
Imágenes
Productos similares
Especificaciones
| Measurements Made | Air temperature, barometric pressure, relative humidity, wind direction, and wind speed. |
| Sampling Rate | 1 Hz |
| Digital Communication Modes | Serial RS-232, RS-485, SDI-12, NMEA, Modbus, ASCII |
| IP Rating | 66 |
| Compliance |
|
| Operating Temperature Range | -40° to +70°C |
| Operating Voltage | 5 to 30 Vdc |
| Typical Current Drain @ 12 Vdc |
|
| Weight | 0.7 kg (1.5 lb) |
Air Temperature Measurement |
|
| Measurement Range | -40° to +70°C |
| Resolution | 0.1°C |
| Accuracy | ±0.3°C (@ 20°C) |
Relative Humidity Measurement |
|
| Measurement Range | 0 to 100% |
| Resolution | 0.1 |
| Accuracy | ±2% @ 20°C (10 to 90% RH) |
Barometric Pressure Measurement |
|
| Measurement Range | 300 to 1100 hPa |
| Resolution | 0.1 hPa |
| Accuracy | ±0.5 hPa (@ 25°C) |
Wind Speed Measurement |
|
| Measurement Range | 0.01 to 60 m s-1 |
| Accuracy |
|
| Resolution | 0.01 m s-1 |
| Starting Threshold | 0.01 m s-1 |
Wind Direction Measurement |
|
| Measurement Range | 0° to 359° |
| Accuracy | ±3° (up to 60 m s-1) |
| Resolution | 1° |
Compass |
|
| Measurement Range | 0 to 359° |
| Resolution | 1° |
| Units of Measure | Degrees |
| Accuracy | ±3° |
Documentos
Folletos producto
Documentos técnicos
Conformidad
Descargas
MetSens500 Example Programs v.1 (5 KB) 25-09-2019
Three CR1000X data logger programs that read the MetSENS500 measurements and sensor status. An example program is included for each output option (RS-232, Modbus, SDI-12).
Preguntas frecuentes
Número de FAQs relacionadas con METSENS500: 1
-
- MetSens has a compass module that outputs at 1 Hz real time without affecting any other measurements, which allows the correction of wind direction if the station is installed on moving ice.
- MetSens has a two-year service life, which is especially helped by the use of a double-louvered radiation shield to reduce the flow of contaminants getting to the temperature/humidity probe.
- MetSens has an option for GPS.
- MetSens has a wind speed resolution of 0.01 m/s, whereas most all-weather sensors have a resolution of 0.1 m/s.
- MetSens has a dew point accuracy of ± 0.3°C, whereas most all-weather sensors have an accuracy of > ±0.7°C.
- MetSens temperature resolution is for the full-range temperature at 0.1°C, whereas other all-weather sensors change to 0.2° at the extremes.
- MetSens offers users the option to use any industry-standard tipping bucket rain gage (MetSens550).
- MetSens provides RS-232, RS-485, Modbus, and SDI-12 from all models.
- MetSens uses Intelligent Signal Processing (ISP) and Adaptive Gain Control (AGC), which have been proven worldwide to provide good quality data.
- MetSens does not indicate a drop in wind speed if the temperature drops or if rain occurs, whereas this is fairly common in other all-weather sensors.