NL116 Interface Ethernet con módulo para CompactFlash
Conectividad Ethernet con ranura para tarjeta CompactFlash
meteorología aplicaciones agua aplicaciones energía aplicaciones flujo gases y turbulencias aplicaciones infraestructuras aplicaciones suelo aplicaciones

Resumen

Ethernet connectivity and expanded data storage capacity are easily added to a CR1000 or CR3000 by attaching an NL116. The Ethernet connection provides access to the powerful Internet capabilities of the data logger for data collection and control. Additionally, gigabytes of data and file storage capacity can be added to the data logger using a removable CompactFlash card.

Leer más

Ventajas y características

  • Provides a native Ethernet connection, allowing the data logger to communicate directly using a variety of Internet protocols
  • CompactFlash cards can be used to greatly expand data storage capacity
  • The ability to remove and swap cards makes retrieving data and files fast and simple
  • Integrated protection for surge and ESD
  • Data-logger-controlled power management for low-power operation

Imágenes

NL116
NL116
NL116
NL116 front view
NL116 back view
NL116 left view
NL116 right view
NL116 top view
NL116 bottom view
NL116 connected directly to the peripheral port of the CR1000 (sold separately)
NL116 attached to the CR3000 (sold separately)

Descripción técnica

Data Storage on CompactFlash Cards

One Type I or Type II (CF) card fits into the NL116’s card slot. Campbell Scientific offers and recommends the CFMC256M, CFMC2G, and CFMC16G CF cards (see Ordering Information). Only industrial-grade CF cards should be used with our products. Although consumer-grade cards cost less than industrial-grade cards, the consumer-grade cards are more susceptible to failure, resulting in both the loss of the card and its stored data. Industrial-grade cards also function over wider temperature ranges and have longer life spans than consumer-grade cards.

The NL116/CF card combination can be used to expand the data logger’s memory, transport data/programs from the field site(s) to the office, and upload power up functions. The computer can read the CF card with the computer’s USB port and the 17752 Reader/Writer.

Especificaciones

Data Logger Interface 40-pin peripheral port on CR1000 or CR3000
Ethernet 10/100 Mbps, auto-detect 10BaseT/100Base-TX, full/half duplex, IEEE 802.3, auto MDI/MDI-X
CompactFlash Cards Campbell Scientific recommends industrial-rated cards.
Power Source 12 V from data logger 40-pin peripheral port
Power Consumption 58 mA typical, 3 mA Ethernet off
Standard Operating Temperature Range -40° to +70°C
Extended Operating Temperature Range -40° to +85°C
Dimensions 10.2 x 8.9 x 6.4 cm (4.0 x 3.5 x 2.5 in.)
Weight 154 g (5.4 oz)

Compliance

Application of Council Directive(s) 2004/108/EC Electromagnetic Compatibility Directive (EMC)
Product Standard EN 61326-1:2013 – Electrical Equipment for measurement, control and laboratory use (EMC requirements – for use in industrial locations)
2011/65/EU The Restriction of Hazardous Substances Directive (RoHS2)

Compatibilidad

Data Logger Requirements

A CR1000 or CR3000 datalogger using operating system version 28 or greater is required.

Preguntas frecuentes

Número de FAQs relacionadas con NL116: 2

  1. The maximum recommended segment length (length of cable between the NL device and the Ethernet repeater, hub, switch, or router it is connected to) for 10Base-T and 100Base-Tx networks using CAT5e cable is 100 m. 

  2. The NL116 is the same as the NL121, with the addition of a CompactFlash card slot that can be used with a removable CompactFlash card to extend data storage and data collection.


Artículos y notas de prensa

Artículos blog