Automatic Water Sampler Maintenance Tips

por Robin Deissinger | Actualizado: 07/29/2015 | Comentarios: 1

Temas Blog


Buscar en el Blog


Suscribirse al Blog

Configure sus preferencias para la recepción de notificaciones por email cuando se publiquen nuevos artículos en el blog que coincidan con sus áreas de interés.


Entre su dirección email:



Sugerir un Artículo

¿Hay algún tema sobre el cual desea saber más? Háganoslo saber. Por favor sea lo más específico que pueda.

Leave this field empty

family of water samplers

If you use automatic water-sampling equipment, consider performing a maintenance check-up during the month of August, which is National Water Quality Month in the U.S. When you perform a maintenance check-up, you can help ensure that your equipment is operating at an optimal level and that you are acquiring accurate water-quality data.

General Maintenance

The need to clean and maintain your Campbell Scientific water-sampling equipment varies depending on the sampler model you are using, as well as the fluid you are sampling and testing. That being said, there are some general maintenance suggestions that you can follow for any of our automatic water samplers:

  1. After collecting the samples and emptying the sample containers, thoroughly clean the sample containers.
  2. Routinely check that all of the tubing is free from cracks or splits.
  3. Replace any parts that are worn.
  4. Replace the tubing if algae or bacterial growth is suspected.
  5. Clean the metering chamber and conductivity rod routinely. 
  6. Check that the water-sample volumes in the sample containers are correct. The volume is controlled by the meter chamber settings. (A significant variance would require further investigation.)
  7. Using the controller, ensure that all of the samples have been collected as programmed. (Missing samples would require further investigation.)
  8. To enable continuous sampling, remove the filled sample containers, and replace them with sanitized, empty sample containers.

Maintenance of the Internal Battery

In addition to performing a general maintenance check-up of your water-sampling equipment, it’s always a good idea to make sure the internal backup battery of the water-sampler controller is working correctly. How long the controller’s internal backup battery lasts depends on how long it remains in disuse, how long it is in use, and the complexity of the running program.

coin-cell and 1/2 AA size cell batteries

A 3.0 Vdc coin-cell battery (pn 15598) and
a 3.6 Vdc 1/2 AA size cell battery (pn 13519).

For the internal battery, Campbell Scientific water samplers commonly use either a 3.0 Vdc coin-cell battery (pn 15598) or a 3.6 Vdc 1/2 AA size cell battery (pn 13519). Typically, your internal battery should provide several years of continued service. For example, under normal operating conditions and temperatures, the 15598 coin-cell battery (used in the PVS5120C and PVS5120D water samplers) has an estimated five-year life expectancy.  

So, how would you know that it's time to change the internal battery? You might suspect that the internal battery is failing if any of these conditions are met:

  • The charge is down considerably (for example, down to 2.9 Vdc for a 3.6 Vdc battery).
  • The sampler clock has drifted outside of the specifications.
  • You notice that your entered programs are not being stored in memory.

3.6 Vdc 1/2 AA size cell battery

When you replace the internal 3.6 Vdc 1/2 AA size cell battery (pn 13519) in the 16-touch keypad controller, follow these steps to keep the new battery from discharging:

  1. Either plug the sampler into an ac power source, or ensure that it has a fully charged external battery.
  2. Make sure the sampler is turned on.
  3. Remove the old internal battery.
  4. Insert the new internal battery.

To replace the 3.6 Vdc 1/2 AA size cell battery, you will need to remove the four screws in the cover of the controller. Carefully lift the lid back so that the connecting cable does not become torn. With the lid in the lifted position, the battery is visible and easily accessible for replacement.

3.0 Vdc coin-cell battery

To replace the 3.0 Vdc coin-cell battery (pn 15598), refer to the instruction manual of the PVS5120-series water sampler. Alternatively, call Campbell Scientific for assistance.

Recommended for You: For more detailed maintenance information, including information about replacing an internal battery, refer to your automatic water sampler’s instruction manual.

Thank you for doing your part—whether in August or some other time of the year—to monitor the quality of our water resources and help minimize the negative impact of neglect, pollution, and overuse.

August is National Water Quality Month

More Information

Do you have questions about automatic water samplers or need help with your Campbell Scientific sampler? Our water-sampler expert at Campbell Scientific would be happy to help you with your portable or stationary sampler needs:


Compartir este artículo


Acerca del autor

robin deissinger Robin Deissinger is the Web Content Specialist at Campbell Scientific, Inc. She creates and maintains content on the company website, which is then shared across the global websites. She also manages the corporate social media program and occasionally contributes blog articles. Robin graduated from Bradley University with a bachelor's degree in communications with an emphasis in advertising, as well as a minor in psychology.

Ver todos los artículos de este autor.


Comentarios

Robin D | 04/15/2019 at 10:13 AM

We retired our line of automatic water samplers on December 31, 2018.

Please log in or register to comment.